|
[Date Prev] [Date Next] [Thread Prev] [Thread Next] [Date Index] [Thread Index]
|
Re: [PLUG] network hardware follies
|
Casey:
On 11/15/2008 11:03 AM, Casey Bralla wrote:
> On Saturday 15 November 2008 9:06:23 am Eric wrote:
>> I'm trying to reset a Linksys RTP300 that my wife obtained for me from
>> Freecycle. It is a Linux-powered VoIP router. The history of the device
>> is unknown but I would presume that it's a former Vonage unit. That may be
>> a totally bogus assumption, I'll admit, but where it came from is
>> irrelevant IF I can get it to work.
>
> If it is the Lynksys, I assume the data on this page may be of big help.
> http://www.linksys.com/servlet/Satellite?c=L_Product_C2&childpagename=US%2FLayout&cid=1119460383933&pagename=Linksys%2FCommon%2FVisitorWrapper
Ah, good. Thanks. I found most of those documents already but not all in one
place.
>> To begin to hack the device I powered it up and held the reset button for
>> about 1 minute (later extended to 3 minutes.) In all cases there is no
>> response from the default address (192.168.15.1 on one of the LAN ports)
>> after the unit was "reset". This mirrors my experience with Linksys
>> devices which appear to resist resetting with a tenacity usually attributed
>> to pitbulls.
>
> That's an odd sounding default address. My guess would be 192.168.1.1, or
> maybe 192.168.2.1.
The documentation claims that 192.158.15.1... yes it does seem odd. If it's in
the 192.168.1.x range then it may clash with my existing network so I'll
improvise a separate hardware connection.
>> The power is there (14.4V) and the LED's light up appropriately. I even
>> opened the device and checked to be sure the reset switch actually had 0
>> volts across it when pressed (of course it did.)
>>
>> The courses of action I can think of are:
>>
>> 1. Use nmap to scan like crazy trying to find the ip address that the unit
>> is using which I presume is in one of these ranges:
>> 192.168.0.0/16 (netmask of 255.255.0.0)
>> OR
>> 10.0.0.0/8 (netmask of 255.0.0.0).
>
>
> These sound like good ranges to search.
>
>> 2. Reset it as before but remove the power supply connection and short the
>> power input leads for about 24 hours to be sure it's really really really
>> powered off. I tried this for 1 minute with no detectable result.
>>
>
> I doubt if anything more than 60 seconds would be necessary.
>
>
>> 3. Place the unit in a local trash receptacle with unusual force.
>>
>
>
> I chuckled at this one. Maybe this is why it was available on freecycle?
So I thought as well - but the original email claimed that it was working. Why
make somebody drive 15 miles to pick up trash was my thought :-)
>> Following course #1 first:
>>
>> I'd like to hook it directly to a pc running Kubuntu and run nmap. Can I
>> use a "crossover" Ethernet cable for that purpose? I just happen to have
>> one. If I do that is the IP address even relevant as long as it goes out
>> of the Ethernet port?
>
>
> Cross over would work for a direct connection. It also might be good to go
> through a hub, just so you can see the blinky-blinky lights.
Have one of those... I'll try it.
>> What kind of nmap scan would be the quickest and still be most likely
>> detect the unit? I tried a ping scan over the home network and it takes
>> about 40 seconds to scan the 192.168.15.1/24 range. At that rate the
>> entire 192.168.1.1/16 range will be about 3 hours. I'm trying not to think
>> about the 10.0.0.0/8 range. Okay, okay... I thought about it: 728 hours or
>> about 1 month. I'd rather try #2 or #3 first :-)
>
>
> I'd do the default nmap scan. You want to look for port 80 (web pages),
> telnet, ssh, and probably some others that I can't think of. The ping may
> not echo, even if you get the correct IP address, so I wouldn't trust a
> simple ping. This may take time to run, but it's a rainy day anyway :)
>
>
>> Ideas and suggestions are really welcome! At this point I'm starting to
>> run out of ideas and #3 is starting to look better and better :-(
>>
>> Eric
Thanks!
Eric
--
# Eric Lucas
#
# "Oh, I have slipped the surly bond of earth
# And danced the skies on laughter-silvered wings...
# -- John Gillespie Magee Jr
___________________________________________________________________________
Philadelphia Linux Users Group -- http://www.phillylinux.org
Announcements - http://lists.phillylinux.org/mailman/listinfo/plug-announce
General Discussion -- http://lists.phillylinux.org/mailman/listinfo/plug
|
|