Doug Crompton on 16 Jan 2006 01:41:20 -0000


[Date Prev] [Date Next] [Thread Prev] [Thread Next] [Date Index] [Thread Index]

Re: [PLUG] Networking question


Most router are default configured to block ICMP traffic (pings) from the
internet WAN side. You 192.168.0.x range is considered internet if it is
on the WAN side.

>From Linksys.....

The Block Anonymous Internet Requests is a feature is designed to prevent
intruders from attacking through the Internet. When it is Enabled, the
Router will drop both the unaccepted TCP request and ICMP packets from the
Internet. The hacker will not find the Router by pinging the Internet IP
address. Click Disabled to allow those packets to get through

On Sun, 15 Jan 2006, Eric wrote:

> A friend of mine who uses SME server (E-smith) has set up his network
> as you'll see below.  He's had me log in and try to fix it but,
> unfortunately, I'm not a networking guru.  Can any of you make sense
> of this and offer some insight?
>
> TIA,
> Eric
>
>
> > Hey Eric:
> >
> > I have the following configuration.
> >
> > E-smith server - 192.168.0.25 - connects to Linksys Router - Wan Interface.
> > Linksys Router Lan is 192.168.1.1
> > I need to get to 192.168.1.200 from the outside interface on the E-smith
> > 192.168.1.200 is hardwired to the router through a switch.
> >
> > I cannot ping 192.168.1.1 from the server even though I added the network to
> > the routing table.
> >
> > I also turned off the firewall functions of the Linksys Router and put
> > 192.168.1.200 on DMZ just to be doubly sure.
> >
> > But since I cannot ping the router what does it matter?
> >
> > My routing table on the e-smith is:
> >
> > Kernel IP routing table
> > Destination Gateway Genmask Flags Metric Ref Use Iface
> > 68.80.190.0 * 255.255.255.0 U 0 0 0 eth1
> > 192.168.1.0 maxserver.maxwe 255.255.255.0 UG 0 0 0 eth0
> > 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0
> > 127.0.0.0 * 255.0.0.0 U 0 0 0 lo
> > default ubr03-a-rtr.chr 0.0.0.0 UG 0 0 0 eth1
> >
> > Everyone on 192.168.1.0 sees 192.168.0.25 just fine - I can see
> > network shares.
> >
> > Why can't I ping the 192.168.1.0 network?
>
>
> --
> ------------------------------------------------------------------------
> #  Eric A Lucas
> #  ------------
> #   "Oh, I have slipped the surly bond of earth
> #    and danced the skies on laughter-silvered wings...
> #        -- John Gillespie Magee Jr.
> ___________________________________________________________________________
> Philadelphia Linux Users Group         --        http://www.phillylinux.org
> Announcements - http://lists.phillylinux.org/mailman/listinfo/plug-announce
> General Discussion  --   http://lists.phillylinux.org/mailman/listinfo/plug
>


"Those that sacrifice essential liberty to obtain a little temporary safety
 deserve neither liberty nor safety."  -- Ben Franklin (1759)

****************************
*  Doug Crompton	   *
*  Richboro, PA 18954	   *
*  215-431-6307		   *
*		  	   *
* doug@crompton.com        *
* http://www.crompton.com  *
****************************


___________________________________________________________________________
Philadelphia Linux Users Group         --        http://www.phillylinux.org
Announcements - http://lists.phillylinux.org/mailman/listinfo/plug-announce
General Discussion  --   http://lists.phillylinux.org/mailman/listinfo/plug